Curb Runner

Engine

• 4045 John Deere/3054 Caterpiller/Cummins B3.3 P

• Temperature Gauge, Oil Pressure Gauge, Volt Meter, Hour Meter, Tachometer, Governor, and Hand Throttle

• High Temperature and Low Oil Pressure Automatic Shut Down

• 12 Volt Electrical System

• 40 Amp Alternator

• 40 Gallon Fuel Tank

• Heavy Duty Battery

Blower Housing

• Replaceable Blower Housing

• #7 & #10 Thick Steel

• 1⁄4” Thick Steel One Piece Replaceable Liner

• Blower is Rated at 22,000 C.F.M.

Impeller

• 30” Diameter

• 3/8” AR-400F Material (Brinell Hardness Exceeding 400)

• 6 Blades and 2 Gussets per Blade

• Impeller is Statically and Dynamically Balanced

Intake Hose and Arm

• 16” Diameter x 120” Long Intake Hose

• Wire Reinforced Hose

Trailer Lighting

• Standard Lighting– Park, Stop, and Turn

• 6 Pole Plug

Machine Will Be Primed and Painted

• Standard Color is Yellow or White

BIG SIX CURB RUNNER

DINKMAR, INC. offers these features:

Engine

• Standard Features

• 10" - 13" Automotive Clutch
• Steel Belt Guard (Opens for Easy Maintenance)
• Common Back Belt Absorbs Shock to Clutch

Blower Housing

• Standard Features

• Roated for 45˚ Exhaust

Impeller

• Standard Features

Intake Hose and Arm

• Standard Features

• Overhead Boom

• 12 Volt-Power Up/Gravity Down

• Engine "Kill" Switch
• Intake is on curb-side of the machine

Exhaust Tube

• Stationary Elbow Square to 16" Round
• 16"x4' Rubber Exhaust Tube

Trailer

• Single Axle (6,000 lbs.)

• 6 Ply x 15” Tires

• 134” length, 80” width, and 116” height

• Rectangular Frame with 31/2” Telescoping Draw Bar and Adjustable Hitch Height

• Bottom of Exhaust Tube at Level Position is 92” to 98” from Ground Up

• Exhaust Tube Extends 12” or more Past Center of Pintle Hitch

• Manual Parking Jack

SPECIFICATIONS

DIMENSIONS
This machine is approximately 134" in overall length, 80" wide outside, and has an overall height of 116". The height, from the ground to the center of the blower housing, is approximately 52". The height, from the ground to the top of the blower housing, is approximately 72". The total weight of the machine is approximately 4000#.

TRAILER:
The main frame is constructed of 4" of 5.4# channel and the sheet steel material is 130" in overall length and 79" in overall width. The trailer has 2 semi-elliptical leaf springs with a 3,500# capacity each. Trailer type axels have a minimum of 3” in diameter with a 6,000# capacity. It is equipped with two; steel disc type wheels with Timken tapered roller bearings. The tires shall be 7:00-15, 8 ply, tubeless type highway tread. The pintle-hook trailer tongue has an adjustable height with manual adjustment from 16" to 32". It is equipped with 3.5" square tubing that is adjustable from 48" to 84" with an eyebolt type drawbar. Also furnished is a top screw, adjustable parking jack with a swiveling caster wheel. The trailer has three safety chains of 3/8" proof coil chain, and are at least 24” to 36" long with chain hooks.

POWER UNIT
The diesel engine is a 4-cylinder 4045D John Deere motor(4045 John Deere/3054 Caterpiller/Cummins B3.3 P). The engine has replaceable wet-sleeve cylinder liners. The engine has a dynamically balanced crankshaft. The power unit is mounted on an adjustable structural steel base. The engine has a 12-volt electrical system with a starter and 60-amp alternator. A heavy-duty battery is included. The power unit includes a dry air-cleaner, 40-gallon fuel tank, and muffler. Radiator is protected by a louvered and perforated radiator screen. The engine is enclosed with two lockable doors. Engine controls consist of a start and stop switch, a voltmeter, a temperature gauge (automatic, high temperature shutdown), an oil pressure gauge (automatic, low-pressure shutdown), and throttle control. All controls are panel mounted. The power unit has a P.T.O. with a 13" Twin Disc clutch. The blower unit is driven from the P.T.O. with one common back belt. A steel belt guard is provided to cover the “V” belt.

BLOWER ASSEMBLY
The blower housing is constructed of #7 and #10 gauge material with a 1/4" plate, full wrap-around, replaceable, abrasive-resistant liner, and a structural angle base. The liner is held in place by bolts. The housing has the following minimum dimensions: 47" high, 45" long, 15" wide, 19" intake opening, and a 14" x 16" exhaust opening. The blower assembly exhausts at 45 degrees from the vertical position. The fan assembly consists of six blades of 3/8" steel plate AR-400F with a Brinell hardness exceeding 400. The fan is electrically welded to a heavy fabricated steel rotor. The blades have no less than a 30” diameter and a 12 1/2” width. The fan is statically and dynamically balanced and has an approved blower capacity that is not less than 22,000 cubic feet per minute. The fan assembly is mounted on a 2-3/16" diameter shaft running on two, large, sealed, self-aligning, pillow block bearings.

EXHAUST ASSEMBLY
Consists of a discharge duct of no less than #10 gauge material for the sides and bottom. The top plate is fabricated from 3/16" material for longer wear. Connected to the discharge duct is a horizontal duct of no less than #12 gauge material. The discharge opening is a 16" round exhaust duct. The 16" round exhaust duct is connected to a 16” diameter by four-foot rubber exhaust hose with a 2” nylon strap and ratchet. The exhaust assembly is mounted to the blower assembly by bolts. At the level position the bottom of the exhaust tube is 92” to 98” from the ground and extends 12” to 18”past the center of the pintle hitch.

UTILITY HOSE
The utility hose has a 16" diameter for maximum suction efficiency and is at least 10 ft. long. The hose is wire-wound, rubber hose with special, abrasive-resistant lining. For easy operating of the utility hose, an electric over-hydraulic pump activates a hydraulic cylinder of at least 2" x 16" and connects to a tubular boom assembly. The operator’s handle assembly has the “THUMB-TOUCH” control switch to raise or lower the utility hand hose during the operation of the leaf loader. Also located on the operator’s handle is an engine “kill” button.

WARRANTY
A two-year warranty covering the leaf vacuum for workmanship and materials is included with the machine.

Factory Set-up can be arranged for. The factory setup includes a factory representative walking the customer through the machine and spending part of the day with the customer operating the machine. Only good for the month of January to September

BIG SIX CURB RUNNER

BIG SIX CURB RUNNER

SPECIFICATIONS

Additional Options